STAME
EN IT
The case · draft 5 · October 2026

A birch console that holds all three.

The MPK mini IV on the left, under an engraved black acrylic mask that rests on it; the macro pad on the right in line with the keys, in a cradle like the Flip's; the Miyoo Flip behind the pad, with the screen at 65°. One black top, at the same height from side to side: 583.5 × 240 mm, 45 mm high. The hub and the cables sit underneath, covered.

Rendering of the console: a birch plywood frame with layered sides, the MPK mini IV under a black engraved mask with glowing pads, the macro pad with clear keycaps and aluminium knobs in its cradle, the white Miyoo Flip open behind the pad with Stame's panel on its screen
Rendered in Blender (Cycles) from the same geometry as the parts to cut and print. The pads glow in the panel's colours, chords in teal and extensions in white (CASE-033); the Flip shows the play page.
Close-up of the macro pad: clear keycaps with paper labels (OPT, SCENE, SAVE LOOP, METRO, FILL, DROP, VIEW, PAGE…), the three aluminium knobs in the cradle, the knob legend engraved on the top, the Flip in its cradle behind
The pad. Clear two-layer keycaps, with a paper label under each cover. The cradle holds the pad's body, and its plate is flush with the black top. What the knobs do is engraved on the top, between the two cradles.
Close-up of the mask: chord types engraved over the pads, extensions and bank B drums under them, the knob names SOUND, PERFORM, FX, KEY, BASS, LOOP, BPM, VOLUME, the transport names
The mask. 2 mm black acrylic, cut and engraved with a diode laser. It rests on the MPK and has an opening for every control, even those Stame does not use: Stame's legends go where a control says nothing or where Stame gives it another job; the MPK's small buttons already carry their names printed on top. The openings come from photographs of the MPK, to about a millimetre.
The console from the front, low: the birch frame, the MPK keys between its two grey end cheeks, the pad in its cradle and the open Flip behind
From the front. One top at the same height from side to side; beside the keys the MPK's grey end cheeks, measured with a ruler.
The console from above: the MPK under the mask on the left, the pad with its fifteen keys at the bottom right, the open Flip behind the pad
From above. The layout Luigi chose: the MPK on the left, the pad in line with the keys, the Flip behind the pad, where the screen does not cover the keys.
The right side of the console: four layers of birch with the name STAME and the mark engraved, the pad, the open Flip under its hood
The side. Four glued layers of birch, with the name and the mark engraved by the laser. The visor closes the Flip's lid at the sides and at the back, and shades the screen.
The console from behind: the birch back with the openings for pedal and audio and the one for the hub's ports, the Flip's black hood
From the back. The back panel sits recessed between the sides, where their curve ends, and the visor covers the white back of the lid. The openings for the pedal and audio; on the right, in the long opening, the side of the hub with the USB-C power input, the USB 2.0 port, SD and microSD.
The Flip's screen close up: Stame's panel with the chord, the tempo, the keyboard and the name of the sound
The screen. Stame's panel on the Flip, at 65° from the top, in the Day theme.
The console in the dark: the Flip's screen in the Night theme and the lit MPK pads light up the black top
In the evening. The Night theme: the screen and the pads give the light.
The console exploded: at the bottom the base, above it the back and the rib, the hub in its holder, the MPK, the cradle and the pad with its clear keys, the mask and the Flip's top, the cradle and the hood, the Flip on top; the sides open outwards
The console exploded, in the order of assembly: the base, back and rib, the hub in its holder, the MPK, the cradle and the pad, the mask and the Flip's top, the Flip's cradle with the hood, the Flip. The sides open outwards.
Assembly

Nine steps, tabs in slots and glue.

No screws in sight: the back, the rib and the front wall lock into the base with tabs, the sides are four layers of 4 mm birch. In amber, the parts each step adds.

Step 1: the two halves of the base
1. The base. Join the two halves of the base at the dovetails, with wood glue. Rubber feet underneath.
Step 2: back, rib and front wall
2. Back, rib and front wall. The back in the notches of the rear edge, with its support layer glued in front; the two layers of the rib glued together and into their slots; the front wall into its own. Glue in the tabs.
Step 3: the sides and the brackets
3. The sides. Glue the four layers of each side: the engraved one outside, the support layer inside, lower where the top rests on it. Then screw them to the base with the six M3 brackets.
Step 4: hub holder, hub and felt on the supports
4. The hub and the cables. Hub holder screwed to the base, the hub inside with its power side in the opening of the back; the post screwed from underneath. The MPK's cable (under the rib) and the pad's (from its cradle) into the front ports; the hub's own cable rises to the OTG slot. Felt on the supports.
Step 5: the pad's cradle, with the pad inside
5. The pad's cradle. The cradle on the base, between rib, side and front wall. The pad inside, its 90° cable through the window at the back.
Step 6: the Flip's top with cradle and visor
6. The Flip's top. The Flip's cradle and the visor screwed to the top (M3 from above, nuts below); the top onto the supports, its front edge on the tooth of the pad's cradle.
Step 7: the MPK and the mask
7. MPK and mask. The MPK in its place, with a 90° USB cable; the mask on top: it rests on the MPK and on the support layers, every control in its opening.
Step 8: the Flip in the cradle
8. The Flip and the cables. The Flip open in the cradle; the OTG through the slot at the back, towards the hub; jack and charging through the one at the front. Headphones in the Flip's jack.
Step 9: the clear keycaps with labels
9. The labels. The clear keycaps on the pad, under each cover its label (etichette_pad.pdf, printed at 100 %).
The parts

Five sheets for the laser, six prints, one sheet of paper.

Sheets of 390 × 390 for an AtomStack S10, nested by material; red is cut, brown is engraved. The sides and the mask carry the same dot lettering as the screen.

Sheet 1, 4 mm birch: the back in two halves, the two engraved outer sides and four inner layers
Birch 4 mm, sheet 1. The back in two halves, with the cable windows; the two outer sides, engraved with the mark and STAMEN HARMONICUM; four inner layers.
Sheet 2, 4 mm birch: the support layers, the rib and the front wall
Birch 4 mm, sheet 2. The support layers of back and sides, lower where the top rests on them; the two layers of the rib; the front wall.
Black acrylic sheet: the engraved mask and the Flip's top
Black acrylic 2 mm. The MPK's mask and the Flip's top, with the legend of the pad's knobs; a 369 × 282 sheet is enough.
Sheet 1, 6 mm birch: left half of the base
Birch 6 mm, sheet 1. The left half of the base, with the dovetails and the notches for the back.
Sheet 2, 6 mm birch: right half of the base
Birch 6 mm, sheet 2. The right half of the base, with the slots for the rib and the front wall.
The label sheet: eight sets of fifteen labels, four light and four dark, in dot lettering
The labels. An A4 at 100 %, eight sets of 15 labels of 10.8 × 8.8 mm: the name in the Matrice dots, DROP, VIEW and PAGE in negative. Light and Night sets.
Print · PETG

The Flip's cradle and visor

A low tray with one cut-out for the jack and the USB-C, open at the back and at the shoulders; a rounded visor that covers the sides and the back of the open lid, printed on its roof.

Print · PETG

Pad cradle, holder, post, brackets

The cradle that holds the pad flush with the top, printed standing up without supports; the hub holder; the post that carries the Flip's top; six M3 brackets between base and sides.

Bought

Felt

1 mm adhesive felt strips on the support layers: the top rests on them at the height of the MPK and does not rattle.

Bought

Clear keycaps, hub, screws

Fifteen clear two-layer keycaps for Cherry MX, a USB-C hub like Luigi's NOVOO 9-in-1, 100 × 44 × 12.5 mm (the holder and the opening in the back are made for its ports), two 90° USB-C cables, M3 × 10 screws and nuts, 3 × 12 wood screws, six rubber feet.

Before cutting

Measured from photographs, checked on paper.

Every measurement lives in one file, misure.py, with its source: [M] manual or datasheet, [O] observed, [D] deduced, [V] to verify. The MPK's controls were measured on a photo from above whose scale holds on both axes, to about a millimetre; the macro pad on ten photos from above and from the side for the layers and the heights, and with a tape measure laid on its plate for the outline (185 × 75 mm, with its front lobe), the knobs, the USB-C socket and the switch on the back; the Flip's ports on two photos that agree within half a millimetre.

Building the 3D model from the parts found real mistakes before any wood was cut: walls overlapping the shelf, screws outside the walls, a cradle covering the shoulder buttons, holes on the mask overlapping, and the engraving on the sides coming out mirrored. Now the generator refuses an engraved part that would read backwards.

The three checks left

  • Print the mask's template at 100 %, check the 100 mm ruler, lay it on the MPK.
  • Cut a test piece to set the laser and the play of the tabs (0.2 mm a side).
  • Check the heights: the MPK's panel and small buttons, the switch at the back of the pad, how far the Flip opens (it needs 115°).
No laser

The same console, all printed, in trays.

For whoever has a 3D printer and no laser. The frame does not copy the laser parts: it is printed in trays, stretches of the console already assembled, standing on their floor on the bed. Each tray has its floor, the side with its profile, the back with its openings, the rib with the cable passage and the ledges for the top; the right one also the pad's cradle, the hub holder and the post. No brackets, no tabs, no glue. On a 240 bed (the Kobra S1) there are three trays, each the full depth; on a 220 bed six. The parts that come off to reach the cables stay separate, the mask in two halves and the Flip's deck, and so do the Flip's cradle and the visor. About 1 kg of PETG or PLA.

The all-printed console: six sand-coloured trays, black mask and deck, the mark and the name raised on the side, the MPK, the pad in its cradle and the open Flip
Drawn from the same STL files that get printed, for a 210 bed: trays in a wood or sand colour, decks and cradles in black.
The six trays apart, with the dovetails in the floor and the walls overlapping at the joints; above, lifted, the mask in two halves, the Flip's deck, its cradle and the visor
The trays. They are lowered next to each other: the dovetails in the floor drop into their sockets from above and keep the trays aligned; the walls that cross a joint overlap at half thickness, with two M3 screws and the nut in its pocket, and hold them together in height. The joints go where they cut no seat and no ledge: under the MPK, between the rib and the pad's cradle, in front of the post.
The test joint: two small pieces with the back overlapping, the pockets for the screw heads and the nuts, a dovetail in the floor and its socket
The test joint. A piece of the joint under the MPK, to print before the trays (about 30 g): the two halves must drop together by hand, with 0.15 mm of play per side in the sockets, and the screws must tighten with the nut in its pocket.
The mask's label sheet: the mark, STAME, the names of the knobs and buttons, black with light lettering
The labels. Each group of lettering on the mask and on the Flip's deck has a pocket 0.4 mm deep; the label is printed 1:1 on sticker paper and goes into it. On the sides the mark and the name are raised.
PDF

Instructions for the printed version

The parts with their sizes and weights, the settings, how the trays join, the lettering and the assembly (in Italian).

istruzioni_stampa3d.pdf

STL

Twelve files

Each one the right way round, the trays standing, within a 210 × 210 mm bed; with stampa3d.py --piatto 240 there are three trays.

stampa3d · list

PDF

Labels

To print at 100 % on sticker paper, with the map of the pockets and a spare set.

etichette_mascherina.pdf

Multicolour: the printer writes the labels

With a multi-filament printer (like the Anycubic Kobra S1 with the ACE Pro) there is one more version, next to this one, for a 240 bed: the same three trays, with the labels printed in the other colour and inlaid flush, three layers deep. The mask and the Flip's deck are printed with the visible face on the bed: it comes out smooth, and the filament changes only happen in the first three layers. On the trays the mark and the name are in the outer face of the side, which is vertical when printed standing: there the filament changes in every layer of the lettering. The labels are redrawn in Matrice, Stame's 5×7 face, with 0.45 mm squares; the decks are black with sand lettering, the trays frame-coloured with black lettering. Each labelled part is a 3MF with both parts and the filaments already assigned.

Half of the mask printed in two colours, as you look at it: black with sand pixel lettering, the mark, STAME and STAMEN HARMONICUM, BEND and MOD, the pads with DIM/6 and B:CHH/KICK below, B: DRUMS under BANK
The left half of the mask, drawn from the files you print. The multicolour files, how to load them in the slicer and the instructions to print (in Italian).

Cream, red and smoke grey

The multicolour version in the three PETG filaments Luigi bought, with a nod to the 8-bit console as it was sold in Europe (the colours only, no marks): cream trays, the tops, the Flip's cradle and the visor in translucent grey, red lettering. The trays use a single filament: the mark and the name on the sides sit on two grey plates with red lettering, printed like the mask and glued into a recess in the side. So the filament only changes in the first three layers of the flat parts, and the slicer job has one plate per main colour. The translucent grey lets some light through: on the mask you can make out the MK4's white panel, the visor is almost black. Rendered in Blender (Cycles) from the same multicolour files, with the new hub in the opening of the back. The parts to print and the Anycubic Slicer Next job, for the Kobra S1: stampa3d_nes (list, instructions, in Italian).

Rendering of the fully printed console: three cream trays with the grey plates on the sides, the smoke grey mask and top with red lettering, the MPK, the pad in its cradle and the Flip open under the smoke visor
The fully printed console, three trays for a 240 bed: cream, red and translucent grey.
The printed mask up close: smoke grey, with the names of pads, knobs and buttons in red
The mask. Translucent grey with red lettering, printed in the second filament flush with the face; the MK4's panel shows faintly underneath.
The macro pad in the cream cradle of the right tray, the smoke top with the red legend of the knobs
The pad. Its cradle is part of the right tray; on the top the legend of the knobs in red.
The printed console from the front, low: the cream trays, the grey mask with red lettering
From the front. The cream trays, a single filament each: each on its own plate, with no changes.
The cream right side with the grey plate, the name STAME and the mark in red, the Flip under the smoke visor
The side. The grey plate with the mark and the name in red, flush in its recess.
The printed console from behind: the cream back with the openings for pedal and audio and the one for the hub's ports
From the back. In the long opening, the side of the hub with the USB-C power input, the USB 2.0 port, SD and microSD.
The printed console in the dark, with the Night theme on the Flip's screen
At night. The Night theme: the screen and the pads make the light.
The printed console exploded: the three trays pulled apart sideways; above, the hub, the MPK, the pad, the two halves of the mask, the Flip's top, the cradle, the Flip and the visor
The three trays pulled apart sideways, as they drop in one beside the other; above, the hub, the MPK, the pad, the mask in two halves, the Flip's top with the cradle, the Flip and the visor.
Files

Everything regenerates from one table of measurements.

PDF

Assembly instructions

Parts and hardware, one step per page, the checks at the end. In Italian.

istruzioni_montaggio.pdf

PDF · SVG · DXF

Cutting sheets

The five sheets 1:1 and the mask's paper template; SVG for LightBurn, DXF for anything else.

progetti_di_taglio.pdf · sheets

STL · PDF

Printed parts and labels

Already turned the right way and resting on the bed; the labels on one A4.

STL · etichette_pad.pdf

3D

Models and renders

SketchUp with one scene per step, OBJ in millimetres, the Blender scene that makes these renders.

stame_console.skp · OBJ · renders

python -I hardware/case/genera.py      # parts, cutting sheets, STL
python -I hardware/case/assieme.py     # 3D model, assembly drawings
python -I hardware/case/stampa3d.py    # the all-printed console, in trays
python -I hardware/case/manuale.py     # PDF: instructions, cutting sheets, printed version
python -I hardware/case/etichette.py   # the keycap labels
python -I hardware/case/rendering.py   # Blender renders (Cycles, CPU)

The scripts, the measurements and the notes are in hardware/case; the requirements in the specification of the case.